Professional drywall installation and interior finishing in the Bay Area. Esquives delivers Level 5 finishes, custom textures, soundproofing, and trim work.
Small holes, nail pops, and hairline cracks in your Bay Area home can usually be patched and blended into the existing texture. When you have extensive water damage, soft or crumbling drywall, large cracks along seams, or multiple repairs in the same area, it’s often more cost‑effective and safer to replace full sections. We’ll inspect the wall or ceiling, check for moisture or structural issues, and recommend the least invasive option that will still look right and last.
Yes, we regularly do texture matching on repairs and additions in Morgan Hill, San Jose, and around the Bay Area. We adjust mud thickness, tools, and spray patterns to match orange peel, light or heavy knockdown, skip trowel, or smooth walls as closely as possible. On older homes, we may do a sample area first so you can approve the match before we finish the whole repair.
Most small to medium drywall repairs (like a few patches or one room) take 1–3 visits over 2–4 days because mud and texture need drying time between coats. Full room or whole‑house installs usually take at least a week, depending on size, complexity, and painting. We’ll walk you through the schedule up front so you know when sanding, texturing, and painting will happen.
We isolate work areas with plastic sheeting, protect floors, and cover nearby furniture when needed. For many jobs we use vacuum‑attached sanders and air filtration to reduce fine dust, which is especially important in occupied Bay Area homes and offices. We also clean up debris each day so you can still use your space as much as possible while we work.
In California, moisture‑prone areas like bathrooms, laundry rooms, and some garages benefit from moisture‑resistant or mold‑resistant drywall rather than standard board. It’s not a substitute for proper waterproofing, but it adds a layer of protection and helps your finishes last longer. We’ll recommend the appropriate board type based on how the room is used, ventilation, and local code.
Fire‑rated drywall is commonly required between attached garages and living spaces, in multi‑family buildings, and in certain commercial walls and ceilings. California building codes and local jurisdictions like San Jose and Morgan Hill specify which walls need a particular fire rating. We’ll review your plans or existing layout and make sure the right type and thickness of board is used in all required locations.
Yes, we install and finish drywall for commercial TI projects, including offices, retail spaces, and light industrial build‑outs throughout the Bay Area and California. That includes framing, sound‑rated assemblies, fire‑rated walls, and smooth or specialty finishes that meet your architect’s specs. We coordinate with other trades and inspections to keep the schedule on track.
First make sure the leak is fully fixed and the area is dry; otherwise any new drywall will quickly be damaged again. For water‑damaged drywall in Morgan Hill or San Jose, we usually remove any soft or moldy sections back to solid material, then install new board, tape, texture, and paint to blend with the existing walls. If we see signs of mold, we’ll advise you if you need a remediation specialist before we close things back up.
We can take your project from bare drywall all the way through priming and painting if you’d like one team to handle everything. New drywall and patches need a quality primer before finish paint for a consistent look. If you already have a painter, we can stop at a ready‑for‑paint finish and coordinate timing so they can start as soon as our work is complete.
Move furniture and valuables at least six feet from any work wall—drywall compound dust travels farther than most people expect and settles on horizontal surfaces well into adjacent rooms. Take down wall art, mirrors, and light fixtures near the work area, and remove or cover electronics in adjacent rooms. Seal HVAC supply and return registers near the work zone to keep fine dust out of the duct system. On our end, we run HEPA-filtered negative air fans, tape poly sheeting over doorways from the work zone, and use vacuum-attached sanders where layout allows. For multi-room projects, we complete the most dust-intensive stages in one area before moving to the next. Even with containment, expect a fine white haze on nearby surfaces after sanding days—it wipes away cleanly with a damp cloth.
A drywall inspection—sometimes called the gypsum board inspection—is required when drywall forms part of a fire-rated assembly: the separation between an attached garage and living space, a party wall in a duplex or townhome, or rated corridor and shaft walls in commercial buildings. At that inspection, the inspector checks board type (Type X or Type C), thickness, fastener pattern and spacing, and whether seams and penetrations are properly handled—all before any tape or compound is applied. For a cosmetic patch on a non-rated interior wall, no inspection is needed. But if your project is running under a building permit, the gypsum board stage is typically a mandatory inspection checkpoint that must be signed off before insulation or finishing work starts.
Small nail holes and minor touch‑ups are reasonable DIY projects, but anything involving large holes, ceiling damage, water issues, or texture matching is where most homeowners run into problems. In Bay Area homes with smooth or custom textures, a patch that isn’t blended correctly will stand out even after paint. If you want the repair to disappear and you’re unsure how to match the existing finish, it’s usually worth bringing us in.
Esquives General Contractors · Morgan Hill, CA · (408) 809-1212 · sales@esquivescontractors.com · Mon–Fri 6:00am–5:00pm, Sat 6:00am–2:00pm · CSLB License #1056641 · Licensed, bonded & insured.